Go Services

In this article below you will find a good deal of great news in relation to Installing A Bathtub.

Setting up a bath tub isn't exactly rocket science, however it does call for solid plumbing, carpentry, and often, tiling abilities. Changing an old bathtub with a brand-new one is additionally a reasonably difficult project. If the old tub is readily available, the job can relocate easily; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old tub as well as set in the new one. Make certain you have qualified yourself for the task and are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed job, it is much better to consider employing one prior to you start. Opportunities are you may need a professional plumber to make tube links.
This write-up will certainly assist you set up a new tub in your restroom if you have already bought a brand-new bathtub and also don't need to transform the setup of your previous water pipelines.
Your devices and also product checklist ought to make up the following:

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Removing Old Touches

If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The process of removing the existing taps can be quite bothersome due to the limited accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipes. When the supply pipes have been removed, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.

Fitting New Touches

If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin ensuring that the washing machines remain in location in between the tap and the sink. Protect the tap in position with the manufacturer offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The previous kind needs to be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

Setting up the Bath tub

Using the two wood boards under its feet, position the bathtub in the needed placement. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The following goal is to make sure that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub up until the level reviews level.
To set up faucets, fit all-time low of the furthest versatile tap adapter to the appropriate supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Turn on the water as well as examine all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the tub as well as additionally examine the overflow outlet and the typical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the maker's user's manual. Tiling and also sealing around the bathtub ought to wait until the bathtub has been utilized a minimum of when as this will certainly resolve it right into its last setting.

Getting ready for the Installment

To start with, the sustaining structure provided with the bathroom ought to be fitted (if needed) according to the producer's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to avoid stress on the bathtub.
Fit the flexible tap connectors to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its final position.

Tiling Around the Bath tub

In the location where the bath fulfills the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, leading to difficulties with moisture and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your components and installations. They are offered in tubes and also cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of drenched paper or soft rope. Remember to constantly fill up the tub with water before securing, to enable the motion experienced when the bathtub remains in use. The sealant can fracture fairly very early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily readily available on the marketplace. It is suggested to fit the floor tiles making use of water-resistant or waterproof glue and cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

As a fervent person who reads on How to Install a Bathtub, I think sharing that piece of writing was worthwhile. Please set aside a second to share this blog posting if you appreciated it. Many thanks for your time. Don't forget to come by our website back soon.

Book Inspection